Ti nspire student software document editor

#Ti nspire student software document editor install

I get lag when using gpsp (this is probably normal though) My nspire takes significantly longer to вЂњwake upвЂќ (so much so that I try not to use it unless I absolutely need to) Calculator doesnвЂ™t charge sometimes (this + grey screen of death = the 10% battery that I currently have) It has happened maybe twice before it happened today. This usually happens after charging my battery the night before. IвЂ™ll remove my calculator from my bookbag to find a grey screen, and a reset shows that my calculator has been running all morning (AP Stats and Chemistry are my last two blocks on B days). The battery percentage is frozen or innacurate (itвЂ™s stuck at 25% right now, but when I reset, my battery percentage is 10% IвЂ™m using an nspire CX-CAS revision I, and of course OS 3.6. IвЂ™ve been using ndless 3.6 since it came out, but recently, IвЂ™ve been having weird problems when ndless is installed.

A NAND corruption (generally caused by a Nover overclocking without following its recommandations).

There are at the time of writingВ no strong relations between these rare failures and Ndless. The TI-Nspire is stuck with a system error at boot time

Now try to open the maintenance menu and follow the procedure above ( вЂњThe TI-Nspire CX falls into a reboot loopвЂќ).

Exit the diags tool by pressing the Reset button at the back of the calculator (thereвЂ™s not exit option in the menus).

Wait for the battery to reach a level of 30%.

Choose the option to run the battery tests.

Hold the the following keys at boot time: Esc+Menu+Minus.

You then canвЂ™t open the maintenance menu as suggested above. The TI-Nspire CX falls into a reboot loop and ran out of battery

Option вЂ4вЂ™ (complete format) will also do, but will also delete all your documents.

Select вЂ2вЂ™ to uninstall the current OS.

If the maintenance menu displays the message вЂњ Replace the battery and try againвЂњ, see below вЂњThe TI-Nspire CX falls into a reboot loop and ran out of batteryвЂќ.

with the TouchPad keypad or the CX: Doc+Enter+EE then ON.

with the ClickPad keypad: Home+Enter+P then ON.

Enter the maintenance menu by turning it on while holding the following keysВ until half the progress bar:.

Reboot the TI-Nspire, by unplugging the USB cable, then removing and putting back a battery on classic TI-Nspire or by pressing the reset button on TI-Nspire CX.

Note that HW-S models are not compatible with OS 3.6, OS >= 3.9.1 is required.В You can find your hardware revision on the back of theВ calculator (the last letter). The TI-Nspire falls into a reboot loopДЇollow Flyingraijin2013вЂ™s video tutorial or the procedure below to uninstall the OS/format your TI-Nspire. It should confirm there is a problem (GPIO error) and will fix it when a key is pressed. Hold Esc+Menu+Minus (Minus near Plus) while pressing the вЂresetвЂ™ button to launch the DiagnosticВ software. This issue is not related to Ndless and may happen on a never-NdlessedВ TI-Nspire. You must reinstall it after each reset The calculator freezes on boot up withВ a black andВ white screen The installation of Ndless is indeed not reboot-proof. After a reset Ndless is not installed anymore Running an executable from the documents screen displays вЂњSorry.

Reset the calculator by pressing the buttonВ under it, and retry the installation procedure. The current version (v3.6) of Ndless makes these instabilities difficult to fix, sorry for the annoyance.

On some calculators the state of the USB connection may change the installation success rate. Try to reinstall Ndless with the USB cable plugged inВ or unplugged. The TI-NspireВ reboots when the scratchpad/a document is opened

#Ti nspire student software document editor install

Reinstall OS 3.9.1В and install Ndless 3.9. One of the side effects is not to be able to use the TI-Nspire without connecting it. HW-S models are not compatible with OS 3.6, OS >= 3.9.1 is required.В You can find your hardware revision on the back of theВ calculator (the last letter, see above). The TI-Nspire turns offВ when not connected to a computer You are opening ndless_installer andВ plugging the calculator to a computer or another TI-Nspire.You have transferred all the following files to your TI-Nspire in a top-level folder named вЂ ndlessвЂ: ndless_installer.tns, ndless_resources_3_9_1.tns and.OS 3.9.1В is installed on your TI-Nspire.OS >= 3.9.1 is required.В You can find your hardware revision on the back of theВ calculator (the last letter).ДЇor Ndless 3.6 :В Recommended for hardware = HW-S Note that HW-S models are not compatible with Ndless 3.6 / OS 3.6. You can post a message to ask for help if you canвЂ™t find whatвЂ™s wrong with your installation. This guide helps you to determine and solve problems encountered when installing Ndless v3.6В or Ndless v3.9.